MPPT100/15 Display LCD

15 amp mppt solar charge controller

100v solar charge controller


Maximum Power Point Tracking Charge Controller

Max PV Source Voltage(open circuit):100VDC

Max Input/Output Current:15 AMPS DC

Max PV power,12V 1a,b):200w

Max PV power,24V 1a,b):400w

Nominal Battery Voltages:12/24/Automatic

Operating ambient Temperature range:-30~60℃(Full rated output up to 40℃)

Dimensions X/Y/Z(mm):136/98/55


MPPT100/15 Display LCD can be used in the maximum 100v solar panel open circuit voltage. battery reverse polarity protection over temperature protection, multi-stage adaptive charging logic greatly prolongs battery life


Programmable battery charge algorithm Day/night timing and light dimming option

Only factory setting


Graphical LCD display


Simple menu-driven operation Programming by buttons

Untra-fastMaximum Power Point Tracking (MPPT)

Especially in case of a clouded sky,when light intensity is changing continuously,an ultra fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.

Load output

Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage.

Alternatively, an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.

Some loads (especially inverters) can best be connected directly to the battery, and the inverter remote control connected to the load output. A special. interface cable may be needed, please see the manual.

Battery Life:intelligent battery management

When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’ state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months.

The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier)until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%.From that point on wards the load

disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.


Solar Charge Controller MPPT  100/15D
System voltage 12/24 V Auto Select
Maximum output current 15A
Maximum PV power, 12V 1a,b) 200W
Maximum PV power,24V 1a,b) 400W
Maximum PV open circuit voltage 100V
Maximum efficiency 98%
Self-consumption 20  mA
Charge voltage ‘absorption’ Default setting:14,4V/28.8 V(adjustable)
Charge voltage ‘float ‘ Default setting:13,8V/27,6 V(adjustable)
Charge algorithm
Temperatre compensation
multi-stage adaptive

-16 mV/℃ resp.-32 mV/℃

Continuous/peak load current 15A/50A
Low voltage load disconnect 11,1V/22,2Vor 11,8V/23,6Vor Battery Life algorithm
Low voltage load reconnect 13,1V/26,2Vor 14V/28Vor Battery Life algorithm
Protection Battery reverse polarity (fuse)/Outp ut short circuit /Over temperature
Operating temperature 30 to +60℃(fullr ated output up to 40°℃)
Humidity 95%,non-condensing
Terminals(fine/single wire) 6mm²/AWG10
Protection category IP22 (connection area)
Weight 0.5kg
Dimensions(X×Y×Z) 136×98×55    mm
Safety EN/IEC 62109
1a) If more PV power is connected, the controller will limit input power to the stated maximum.
1b) PV voltage must exceed Vbat +5V for the controller to start. Thereafter minimum PV votage is Vbat+1V


Home Off-Grid & Back-Up Power Solutions

RV Solar power system solutions

Marine Power Solutions


There are no reviews yet.

Be the first to review “MPPT100/15 Display LCD”

Your email address will not be published. Required fields are marked *

A Sale Promotion

A description of the promotion and how the visitor could claim the discount