Description
Untra-fast Maximum Power Point Tracking (MPPT)
Especially in case of a clouded sky, when light intensity is changing continuously, an ultra fast MPPT controller will improve energy harvest by up to 30%compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.
Load output
Over-discharge of the battery can be prevented by connecting all loads to the load output. The load output will disconnect the load when the battery has been discharged to a pre-set voltage.
Alternatively,an intelligent battery management algorithm can be chosen: see Battery Life. The load output is short circuit proof.
Some loads(especially inverters)can best be connected directly to the battery, and the inverter remote control connected to the load output. A special interface cable may be needed, please see the manual.
Battery Life: intelligent battery management
When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a ‘partially charged’state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months.
The Battery Life algorithm will monitor the state of charge of the battery and, if needed, day by day slightly increase the load disconnect level (i.e. disconnect the load earlier) until the harvested solar energy is sufficient to recharge the battery to nearly the full 100%.From that point on wards the load disconnect level will be modulated so that a nearly 100% recharge is achieved about once every week.
Programmable battery charge algorithm
See the software section on our website for details
Day/night timing and light dimming option
See the software section on our website for details
| MPPT 100/30 | MPPT 100/50 | |
| System voltage | 12/24 V Auto Select | |
| Maximum output current | 30 A | 50 A |
| Maximum PV power,12V 1a,b) | 440 W(MPPT range 15 Vto 80 V) | 700 W(MPPT range 15Vto 70V resp.95V) |
| Maximum PV power,24V 1a,b) | 880 W(MPPT range 30Vto 80 V) | 1400 W(MPPT range 30Vto 70V resp.95V) |
| Maximum PV open circuit voltage | 100 V | |
| Maximum efficiency | 98 % | |
| Selfconsumption | 10 mA | |
| Charge voltage ‘absorption’ | Default setting:14,4V/28.8V(adjustable) | |
| Charge voltage ‘float’ | Default setting:13,8V/27,6V(adjustable) | |
| Charge algorithm | multi-stage adaptive | |
| Temperature compensation | -16mV/°Cresp.-32mV/℃ | |
| Protection | Battery reverse polarity(fuse, not user accessible) Output short circuit Over temperature (MPPT 100/50:PV reverse polarity) |
|
| Operating temperature | -30 to +60℃(full rated output up to 40°℃) | |
| Humidity | 95%,non-condensing | |
| Data communication port | VE.Direct See the data communication white paper on our website |
|
| ENCLOSURE | ||
| Colour | Blue (RAL 5012) | |
| Terminals(fine/ single wire) | 13 mm²/AWG 6 | |
| Protection category | IP43 (electronic components), IP22 (connection area) | |
| Weight | 1,25 kg | |
| Dimensions (XxYxZ) | 130x 186×70 mm | |
| STANDARDS | ||
| Safety | EN/IEC 62109 | |
| 1a)If more PV power is connected, the controller will limit input power to 440W resp.880 W(MPPT 100/50:700W resp.1400W) 1b) PV voltage must exceed Vbat + 5Vfor the controller to start.Mereafter minimum PVvoltage is Vbat + 1V |
||
Application
Home Off-Grid & Back-Up Power Solutions
Reviews
There are no reviews yet.